Checkering tool complete T-24, 60°

Checkering tools from T-series has three cutting parts. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The beech handle is well balanced and easy to use.

At the same time cut all three blades with equally spaced teeth, so you can quickly apply the pattern immediately to a large area. This speeds up the process of drawing the picture, eliminates the additional effort. The lines are parallel with a single pass.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smooth turns every groove.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering layout guide / butt scribe

Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.

Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.

Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

550p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete BBT 11/16`

Rubber mounted, chatter-free cutters, shave out excess wood without "digging in". Leaves barrel channel smooth and ready for barrel, without gouging, rasping or final sanding.

 

2400p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete BBT 3/4`

Rubber mounted, chatter-free cutters, shave out excess wood without "digging in". Leaves barrel channel smooth and ready for barrel, without gouging, rasping or final sanding.

 

2970p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete B-1

Checkering too B-1, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete B-2

Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete B-3

Checkering tool B-3 is a single blade with teeth. Profile cutter convex semicircular designed to perform the edging pattern. The tool leaves a concave semicircular groove. Good for beginners, as forgiving some mistakes in the work. All cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. maximum groove depth 2.8 mm, width 2.8 mm.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete C-1, 60°

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete C-1, 90°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L- 9, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L- 9, 90°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L-10, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L-10, 90°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L-11, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L-11, 90°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L-12, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete L-12, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p(0)
Отзывов: 1
Рейтинг :

Checkering tool complete N2-16, 60°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Item code Item Cutting angle

Teeth per inch

М00015687 N2-16 60° 16
М00015638 N2-16 90° 16
М00015688 N2-18 60° 18
М00015669 N2-18 90° 18
М00015689 N2-20 60° 20
М00015662 N2-20 90° 20
М00015690 N2-22 60° 22
М00015637 N2-22 90° 22
М00015691 N2-24 60° 24
М00015676 N2-24 90° 24

 

 

900p(0)
Отзывов: 1
Рейтинг :

Резцы для чекеринга

В этом каталоге вы найдете и сможете купить инструменты для разметки и нанесения чекеринга. Чекеринг - вид украшения или даже вид резьбы на деревянных изделиях в виде параллельных насечек, ромбов и линий. Очень популярно нанесение данной резьбы на приклады, рукояти ножей, вазы и другие предметы, где требуется надежный хват. В минимально необходимы набор для нанесения чекеренга входят резцы одного размера или шага. Резец для нанесения первой канавки - резец с одной режущей кромкой, резец для нанесения параллельных канавок с левой или правой режущей кромкой (РК) и штихель для зачистки и подрезки мест, куда не достали другие резцы. Так же вам могут понадобиться и инструменты для удобства разметки чекеринга, особенно параллельные изогнутым формам.

Видеоматериалы

youtube video
youtube video

Нож для резьбы по дереву, ПЕТРОГРАДЪ, Богородский, 200мм/60мм

Нож резчицкий ПЕТРОГРАДЪ, Богородский, 190мм/60мм. Резчицкие ножи общего назначения, а также для большого удаления материала. Отличный нож как для начинающих так и для профессионалов. Все ножи заточены и готовы к работе.
Для выбора нужного ножа нажмите на название товара
2700p
Отзывов: 1
Рейтинг:

Нож для резьбы по дереву, ПЕТРОГРАДЪ, финский, 180мм/40мм

Резчицкие ножи с острым кончиком предназначены для деталировки и работы в труднодоступных местах. Длина лезвия 45мм или 60мм, скругленный обух. Угол заточки 23±2°. Удобная овальная рукоять из ценных пород древесины, покрыта маслом. Длина рукояти - 115мм. Отличный нож как для начинающих так и для профессионалов. Лезвие толщиной 2,5мм выполнено из высокоуглеродистой стали с закалкой до твердости 59-61 HRc. Все резцы заточены и готовы к работе. Производство Петроград (Россия).
Для выбора нужного ножа нажмите на название товара
2500p
Отзывов: 1
Рейтинг:

Резец для чекеринга C-1, 60° (одна РК)

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

900p
Отзывов: 1
Рейтинг:

Резец для чекеринга C-1, 90° (одна РК)

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

900p
Отзывов: 1
Рейтинг:

Топор кованый ПЕТРОГРАДЪ, модель Рославль 7, топорище н11, РК - сканди

Топор кованный походный с изогнутой рукоятью. Общая длина - 370 мм. Высота топора - 140 мм. Длина режущей кромки - 120 мм. Топор выкован вручную из стали 65Г. Заточка прямая. Общая масса - 0,7 ± 0,05 кг. В комплекте кожаный чехол для защиты лезвия. Топорище выполнено из древесины клёна, длиной 320 мм. Топор отлично сбалансирован и подойдет для огромного вида работ, как походный топор, для небольших плотницких и столярных работ и просто как универсальный топор. 

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

13000p
Отзывов: 1
Рейтинг:
new

Нож для резьбы по дереву, ПЕТРОГРАДЪ, Ложкорез, модель N1/22, левый

Ложкорез по дереву ПЕТРОГРАДЪ модель N1/22, это инструмент для резьбы деревянных ложек и других впуклых поверхностей. Основная задача ложкореза - выборка лунки в деревянной ложке (черпало). Выпускается двух видов: правый и левый. Производство фабрика Петроградъ (Россия)

3200p
Отзывов: 1
Рейтинг:
new

Нож для резьбы по дереву, ПЕТРОГРАДЪ, флажок 45град, 180мм/40мм

Нож для резьбы по дереву, ПЕТРОГРАДЪ, косая заточка 45град. Предназначен для широкого спектра работ. Рукоять выполнена из ясеня, угол скоса 45 градусов, инструментальная сталь. Производство фабрика Петроградъ (Россия).

2500p
Отзывов: 1
Рейтинг:

Стамеска ПЕТРОГРАДЪ, серия Нева, 6мм

Стамеска ПЕТРОГРАДЪ, серия Нева, 6мм. Стамески спроектированы, ориентируясь на многолетний опыт мастеров-краснодеревщиков. Форма лезвия имеет боковые скосы для работы в труднодоступных местах, например при подрезке и подчитки шиповых соединений: ласточкин хвост, шип-проушина, впол дерева, сковородней и прочие. Производятся с различной шириной полотна от 3мм до 26мм. Толщина лезвия переменная и увеличивается от режущей кромки к рукояти. Производство фабрика Петроградъ (Россия)

3300p
Отзывов: 1
Рейтинг:
new%

Топор кованый ПЕТРОГРАДЪ, модель Рославль 10, топорище н25

Топор кованый ПЕТРОГРАДЪ, модель Рославль 10, топорище н25. Отличается от других топоров удлиненной режущей кромкой. Благодаря этой особенности топор можно брать близким к полотну хватом и не бояться поранить руку при работе. Такой хват очень удобен при тёске и ошкуривании бревен. Удлиненная рукоять позволяет без лишних усилий рубить ветки и сучья. Производство фабрика Петроградъ (Россия).

15000p
Отзывов: 1
Рейтинг:
new

Масло камелии, KAPLEUM, Лаванда, 60 мл.

Масло камелии, KAPLEUM, Лаванда, 60 мл. Неформальная творческая группа GILDIA.PRO предлагает новый продукт, изготовленный на основе отлично зарекомендовавшего себя масла Камелии – KAPLEUM.

 

720p
Отзывов: 1
Рейтинг: